STANDARD Tint RF Colors – Standard Colors

STANDARD™ Tint RF Colors

Developed for Water-Based

STANDARD™ Tint RF colors are high-strength, high-quality aqueous pigment dispersions in water-borne acrylic resin.

STANDARD™ Tint PR colors contain no surfactants that can often interfere with printing ink performance and durability. In laboratory tests STANDARD™ Tint PR colors have been shown to produce prints with high gloss, optimum rheology and extended stability.

In addition to their applications in the ink industry, STANDARD™ Tint RF products are often used in the coloring of rubber latex, coatings, textile printing and paper coating.

Masstone Shade	1/20 Tint Tone	STANDARD™ Tint RF Colors	CI No.	% Pigment	Bleed Resistance							Heat Fastness		Light Fastness
Masstone Shade	1/20 Tint Tone	STANDARD™ Tint RF Colors	CI No.	% Pigment	Acid	Alkali	Water	Ethanol	Glycol	Paraffin Wax	Soap	15min 150°C	30min 150°C	MT	TT
		STANDARD™ Tint RF Yellow 1014	PY 14
		STANDARD™ Tint RF Yellow 1614	PY 14
		STANDARD™ Tint RF Yellow 1174	PY 74
		STANDARD™ Tint RF Yellow 1083	PY 83
		STANDARD™ Tint RF Yellow 1183	PY 83
		STANDARD™ Tint PR Yellow 1151	PY 151
		STANDARD™ Tint RF Yellow 1181	PY 181
		STANDARD™ Tint RF Orange 2016	PO 16
		STANDARD™ Tint RF RED 3522	PR 22
		STANDARD™ Tint RF RED 3523	PR 23
		STANDARD™ Tint RF RED 3571	PR 57:1
		STANDARD™ Tint RF RED 3122	PR 122
		STANDARD™ Tint RF RED 3176	PR 176
		STANDARD™ Tint RF RED 3238	PR 238
		STANDARD™ Tint RF RED 3266	PR 266
		STANDARD™ Tint RF VIOLET 4023	PV 23
		STANDARD™ Tint RF BLUE 5150	PB 15:0
		STANDARD™ Tint RF BLUE 5153	PB 15:3
		STANDARD™ Tint RF GREEN 6007	PG 7
		STANDARD™ Tint RF BLACK 8007	PBK 7
		STANDARD™ Tint RF WHITE 9016	PW 6

Procedures:

Dyeing at 140º

Pre-scour with 1& STANSCOUR® BRC at 160º for 20-minutes.

Drop & rinse.
Set bath at 90ºF with:
1. Xg/l salt (per chart below)
Add PERMARBIL® Reactive Dye (pre-dissolve in 160º-180ºF water).
Run 10-minutes.
Add 1/10 total amount of Soda Ash over 10-minutes.
1. Run 10-minutes.
Add remaining 9/10 Soda Ash over 10-minutes (pH 10.8-11.2).
1. Run 10-minutes.
Heat to 140ºF at 2ºF/minute.
1. Run for 45-minutes.
Sample.
1. If shade is acceptable, drop bath.
2. When sampling shade, swatch should be: rinsed cold, rinsed warm, and neutralized with 0.25% Acetic Acid. Then, scoured at 200ºF – see steps 12-18.
Rinse at 120ºF for 10-minutes.
1. Drop bath.
Rinse at 140º for 10-minutes.
1. Drop bath.
Neutralize at 120ºF with 0.25% Acetic Acid (pH 7-8).
1. Run 10-minutes.
2. Drop bath.
Set fresh bath to 120ºF.
Heat to 200ºF.
1. Hold 10-minutes.
2. Drop bath.
Set bath to 120ºF.
1. Hold 10-minutes.
2. Drop bath.
Finish as usual.

Salt and Soda Ash Recommendations for Cotton/Rayon

% Reactive Dye	g/l Sodium Chloride or Sodium Sulfate	g/l Soda Ash
0-0.25	30	5
0.26-0.50	50	5
0.51-1.00	60	10
1.01-2.00	60	10
2.01-3.00	80	10
3.01-5.00	80	10
Above 5.00* *When dyeing above 5.00% the yield should increase with use of 100g/l salt	80-100	10

PERMABRIL® Brill Blue R Special Requires Reduced Salt

% Reactive Dye	g/l Sodium Chloride or Sodium Sulfate
up to 0.50	20
0.51-2.00	30
2.01-4.00	40
Above 4.00	50

Colors May Vary Across Screens The shades illustrated on this website are intended to convey the general color characteristics of each dye and are not intended to be an accurate representation of how the finished dyeings will actually appear. Due to differences in computer monitors, screen resolutions and graphics cards, the colors displayed here may vary.